Introduction to the NEC MultiSync LCD2110
E - 1
Introduction to the NEC MultiSync LCD2110
Congratulations on your purchase of the NEC MultiSync LCD2110 true
colour monitor!
NuCycle Plastic
A special silicone compound for PC resin, being extremely flame-
retardant, safe and environmentally friendly.
Wide Viewing Angle Technology
Allows the user to be able to see the monitor from any angle(170 degrees)
from any orientation – Portrait or Landscape. Provides full 170˚ viewing
angles either up, down, left or right.
Analog Advantage
Capable of displaying unlimited colours in a continuous spectrum,
providing a truer representation of colour. The monitor’s high contrast
LCD enhances colour vibrancy and improves focus with no geometric
distortion.
Wider Compatibility
Because the MultiSync LCD monitor is analog through and through, it
does not require special analog to digital display or interface cards but
can accept RGB input directly.
Reduced Footprint
Provides the ideal solution for environments requiring superior image
quality but with size and weight limitations. The monitor’s small footprint
and low weight allow it to be moved or transported easily from one
location to another.
Colour Control system
Allows you to adjust the colours on your screen and customize the colour
accuracy of your monitor to a variety of standards.
78134811.PM5
11
99.12.24, 2:19 PM
Introduction to the NEC MultiSync LCD2110
E - 3
FullScan Capability
Allows you to use the entire screen area in most resolutions, significantly
expanding image size.
VESA Standard Mounting Interface
Allows users to connect their MultiSync monitor to any VESA standard
third party mounting arm or bracket. Allows for the monitor to be
mounted on a wall or an arm using any third party compliant device.
BNC/D-SUB
Offers dual inputs, allowing you to connect the monitor to one system
via a BNC cable and a another system via a standard D-Sub cable. You
can easily switch between computers with a touch of a button on the up-
front control panel.
78134811.PM5
13
99.12.24, 2:19 PM
E - 4
Contents of Package
Contents of Package
Your new MultiSync LCD monitor box should contain the following:
MultiSync LCD2110 monitor
with 15-pin VGA to BNC Cable
and AC Adapter
–
–
–
–
–
–
NEC MultiSync LCD2110 (Model LA-2141JMW-P)
AC power cable.
AC Adapter. (Type A2440S01)
Video Signal Cable – 15 pin VGA to BNC.
User’s manual.
NEC LCD Setup Software, Pivot Software and other helpful
files.
Remember to save the original box and packing materials to transport or
ship the monitor.
78134811.PM5
14
99.12.24, 2:19 PM
Recommended Use
E - 5
Recommended Use
For optimum performance, please note the following when setting up
and using the MultiSync LCD2110 colour monitor:
DO NOT OPEN THE MONITOR. There are no user
•
serviceable parts inside and opening or removing covers may
expose you to dangerous shock hazards or other risks. Refer
all servicing to qualified service personnel.
The optimum monitor position is facing away from direct
sunlight.
•
Allow adequate ventilation around the monitor so that heat can
•
properly dissipate. Do not block ventilated openings or place
the monitor near a radiator or other heat sources. Do not put
anything on top of monitor.
Do not spill any liquids into the cabinet or use your monitor
near water.
•
Do not insert objects of any kind into the cabinet slots, as they
may touch dangerous voltage points, which can be harmful or
fatal or may cause electric shock, fire or equipment failure.
•
Do not place any heavy objects on the power cord. Damage to
the cord may cause shock or fire.
•
Do not place this product on a sloping or unstable cart, stand or table,
as the monitor may fall, causing serious damage to the monitor.
•
Use the monitor in a clean and dry area.
•
•
Handle with care when transporting. Save packaging for
transporting.
The power cable connector is the primary means of detaching
the system from the power supply. The monitor should be
installed close to a power outlet which is easily accessible.
•
Use supplied AC Adapter.
•
•
The inside of the fluorescent tube located within the LCD
monitor contains mercury. Please follow the bylaws or rules of
your local municipality to dispose of this tube property.
Clean the LCD monitor surface with a lint-free, non-abrasive cloth.
Avoid using any cleaning solution, glass cleaner or tissue paper.
•
78134811.PM5
15
99.12.24, 2:19 PM
E - 6
Recommended Use
For optimum performance, allow 20 minutes for warm-up.
Avoid displaying fixed patterns on the monitor for long periods
of the time to avoid image persistence (after-image effects.)
•
•
Avoid applying pressure to the LCD monitor surface.
•
•
This MultiSync LCD monitor is integrated with OptiShield
protective glass that helps protect your valuable and potentially
fragile LCD panel.
Please note that OptiShield glass is not safety glass and is not
laminated. As with other glass, OptiShield glass may break
into sharp pieces if abused, dropped, or otherwise subjected to
a substantial shock. If OptiShield does break, please use care
to avoid injury.
MultiSync brand monitors equipped with OptiShield glass will
have a reflective surface which, under normal lighting
conditions, can cause eyestrain if viewed for long periods of
time. To avoid eyestrain, we recommend these monitors be
used in applications — such as information kiosks, industrial
plants, machinery control systems, and trading floors — where
the screens will be viewed only intermittently.
Immediately unplug your monitor from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
When the power supply cord or plug is damaged.
If liquid has been spilled or objects have fallen into the monitor.
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet is damaged.
If the monitor does not operate normally by following operating
instructions.
•
•
•
•
•
CAUTION:
Allow adequate ventilation around the monitor so that heat can
•
properly dissipate. Do not block ventilated openings or place
the monitor near a radiator or other heat sources. Do not put
anything on top of monitor.
The power cable connector is the primary means of detaching
the system from the power supply. The monitor should be
installed close to a power outlet which is easily accessible.
•
Use caution when carrying the monitor, as the compact stand
may extend automatically.
•
78134811.PM5
16
99.12.24, 2:19 PM
Recommended Use
E - 7
Handle with care when transporting. Save packaging for
transporting.
•
•
This LCD monitor is designed for use with a flexible arm,
therefore it is delivered without stand. Please use the attached
screws (4pcs) when installing. To fulfil the safety requirements
the monitor must be mounted to an arm which guaranties the
necessary stability under consideration of the weight of the
monitor. The LCD monitor shall only be used with an approved
arm (e.g. GS mark).
CORRECT PLACMENT AND ADJUSTMENT OF THE MONITOR
CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK
THE FOLLOWING WHEN YOU POSITION THE MONITOR:
Adjust the monitor height so that the top of the screen is at or
slightly below eye level. Your eyes should look slightly
downward when viewing the middle of the screen.
•
Position your monitor no closer than 40 cm and no further away
than 70 cm from your eyes. The optimal distance of MultiSync
LCD2110 is 61 cm.
•
Rest your eyes periodically by focusing on an object at least
6 m away.
•
Position the monitor at a 90° angle to windows and other
light sources to minimize glare and reflections. Adjust the
monitor tilt so that ceiling lights do not reflect on your screen.
•
If reflected light makes it hard for you to see your screen, use
an anti-glare filter.
Adjust the monitor’s brightness and contrast control to enhance
readability.
•
•
Use a document holder placed close to the screen.
•
•
Position whatever you are looking at most of the time (the screen
or reference material) directly in front of you to minimize
turning your head while you are typing.
Get regular eye checkups.
•
78134811.PM5
17
99.12.24, 2:19 PM
E - 8
Installation
Installation
Connection to your Personal Computer
The MultiSync LCD2110 true colour monitor complements PC compatible
computers. Your system has one of two configurations:
–
–
the video controller is built into the computer.
the video controller is in the form of a display card (sometimes
referred to as graphics card, video adapter or graphics board).
Both configurations have a video connector (or a CRT PORT on laptop
computers). If you are not sure which connector is the video connector,
refer to your computer or display card manual.
To attach the MultiSync LCD2110 monitor to your system,
follow these instructions:
1. Turn off the power to your computer.
2. Connect the 15-pin mini D-SUB of the appropriate signal
cable to the connector of the display card in your computer
(Figure A.1) (Figure B.1). Tighten all screws.
NOTE: Some Macintosh systems require a Macintosh cable adapter.
3. Remove connector cover on back of monitor. Connect the BNC
cables and AC adapter cable to the appropriate connectors on
the back of the monitor.
If you are using the supplied video signal cable, continue to step 4.
If you are using a 15-pin mini D-SUB cable (not included), please
skip to Step 5.
4. Connect the red BNC cable to the BNC connector on the
monitor labeled R, the green BNC cable to the BNC connector
labeled G/Sync, the blue BNC cable to the BNC connector
labeled B. If you have a fourth BNC connector (Composite
Sync), connect it to the BNC connector on the monitor labeled
HS/CS. If you have a fifth BNC connector (Vertical Sync),
connect it to the BNC connector on the monitor labeled VS
78134811.PM5
18
99.12.24, 2:19 PM
Installation
E - 9
(Figure C.1). Place the 15-pin VGA to BNC Cable under clip
A (Figure D.1A). Then place the 15-pin VGA to BNC cable
under Clip B (FigureD.1B).
5. Connect the D-SUB cable to D-SUB connector on the back of
the monitor (Figure C.2).
6. Replace connector cover.
NOTE: Incorrect cable connections may result in irregular operation,
damage display quality/components of LCD module and/or shorten the
module’s life.
7. Connect one end of the power cord to the AC Adapter and the
other end to the power outlet (Figure E.1).
8. Turn on the monitor (Figure F.1) and the computer.
78134811.PM5
19
99.12.24, 2:19 PM
E - 10
Installation
9. To complete the setup of your MultiSync LCD monitor:
A. Set the resolution to 1600 x1200 @60 Hz.
B. Use the following OSM controls:
•
•
•
Auto Adjust Contrast
Auto Adjust
Image Adjust – Fine
NOTE: Manual adjustment of the H/V Position and Image Adjust H.
Size / Fine controls may be required to complete setup of your MultiSync
monitor. For a full description of these OSM controls, refer to the
Controls section of this User’s Manual.
10. Refer to User’s Manual in the NEC LCD Setup Software CD
case for installation and operation of this software.
NOTE: If you have any problems, please refer to the Troubleshooting
section of this User’s Manual.
Figure A.1
Figure B.1
78134811.PM5
20
99.12.24, 2:19 PM
Installation
E - 11
R
G(/ SYNC)
B
HS/ CS
VS
Figure C.1
Figure C.2
Figure E.1
Power
Button
Clip
A
Clip
B
Figure F.1
Figure D.1A
Figure D.1B
Raise and Lower Monitor Screen
The monitor may be raised or lowered in either Portrait or Landscape
mode.
To raise or lower screen, place hands on each side of the monitor and
lift or lower to the desired height (Figure RL.1).
Screen Rotation
Before rotating, the screen must be raised to the highest level to avoid
knocking the screen on the desk or pinching your fingers.
To raise the screen, place hands on each side of the monitor and lift up
to the highest position (Figure RL.1).
To rotate screen, place hands on each side of the monitor screen and
turn clockwise from Landscape to Portrait or counter-clockwise from
Portrait to Landscape (Figure R.1).
To toggle the orientation of the OSM menu between Landscape and
Portrait modes, press the RESET button while OSM menu is off.
78134811.PM5
21
99.12.24, 2:19 PM
E - 12
Installation
Tilt and Swivel
Grasp both sides of the monitor screen with your hands and adjust the
tilt and swivel as desired (Figure TS.1).
Figure RL.1
Figure R.1
Figure TS.1
78134811.PM5
22
99.12.24, 2:19 PM
Installation
E - 13
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1. Disconnect all cables.
2. Place hands on each side of the monitor and lift up to the highest
position (Figure RL.1).
3. Place monitor face down on a non-abrasive surface (Place the
screen on a 55mm platform so that the stand is parallel with
the surface.) (Figure S.1).
55mm
Figure S.1
4. Press the " " portion with your index finger and at the same
time slide the lower stand cover (Figure S.2).
Next, lift up the stand, remove the lower stand cover, then go
on to remove the upper stand cover (Figure S.3).
Return the stand to its original position, remove the 4 screws
that connect the monitor to the stand, and lift off the stand
assembly (Figure S.4).
5. Reverse this process to reattach stand.
NOTE: Use only VESA-compatible alternative mounting method.
4
3
1
2
Figure S.2
Figure S.3
Figure S.4
78134811.PM5
23
99.12.24, 2:19 PM
E - 14
Controls
Controls
BNC/D-SUB:Allows you to change between the BNC and D-SUB signal
inputs.
OSM Controls
OSM
The OSM controls on the front of the monitor provide the following
functions:
To access OSM press any of the control buttons (
EXIT button.
,
,
,
) or the PROCEED or
To rotate OSM between Landscape and Portrait modes, press the RESET button.
NOTE: OSM menu must be closed in order to rotate.
Main Menu
Sub-Menu
EXIT
Exits the OSM controls.
Exits to the OSM main
menu.
CONTROL
/
Moves the highlighted
area up/down to select
one of the controls
Moves the highlighted
area up/down to select
one of the controls
CONTROL
/
Moves the highlighted area Moves the bar left /
left / rights to select
control menus.
Has no function.
right to increase or
decrease the adjustment.
Activates Auto Adjust
and ALL RESET functions.
Resets the highlighted
contol to the factory
setting.
PROCEED
RESET
Resets the highlighted
contol menu to the factory
setting.
NOTE: When RESET is pressed in the main and sub-menu, a warning window will
appear allowing you to cancel the RESET function by pressing the EXIT button.
78134811.PM5
24
99.12.24, 2:19 PM
Controls
E - 15
Brightness/Contrast Controls
BRIGHTNESS
Adjusts the overall image and background screen brightness.
CONTRAST
Adjusts the image brightness in relation to the background.
AUTO ADJUST CONTRAST
Adjusts the image displayed for non-standard video inputs.
Auto Adjust
Automatically adjusts the Image Position, H. Size and Fine
settings.
NOTE: ManualadjustmentoftheH/VPositionandImageAdjust
H. Size / Fine controls may be required to complete setup of
your MultiSync monitor.
Position Controls
H. POSITION
Controls Horizontal Image Position within the display area
of the LCD.
V. POSITION
Controls Vertical Image Position within the display area of
the LCD.
AUTO
Automatically sets the Horizontal and Vertical Image
Position within the display area of the LCD.
78134811.PM5
25
99.12.24, 2:19 PM
E - 16
Controls
Image Adjust Controls
H. SIZE
Adjusts the horizontal size by increasing or decreasing this
setting.
FINE
Improves focus, clarity and image stability by increasing or
decreasing this setting.
Automatically adjusts the H. Size and Fine settings.
Colour Control System
Five colour presets select the desired colour setting. Each
colour setting is adjusted at the factory.
R,G,B: Increases or decreases Red, Green or Blue colour
depending upon which is selected. The change in colour will
appear on screen and the direction (increase or decrease)
will be shown by the bars.
Tools
OSM H. POS.
OSM V. POS.
You can choose where you would like the OSM control
window to appear on your screen. Selecting OSM Location
allows you to manually adjust the position of the OSM
control menu left, right, up or down.
ALL RESET
Selecting ALL RESET when BNC input is selected allows
you to reset all OSM control settings for the BNC input back
to the factory settings.
Selecting ALL RESET when D-SUB input is selected allows
you to reset all OSM control settings for the D-SUB input
back to the factory settings.
Individual settings can be reset by highlighting the control
to be used and pressing the RESET button.
78134811.PM5
26
99.12.24, 2:19 PM
Controls
E - 17
Information
Indicates the current display resolution, frequency setting
and type of Sync signal of the monitor.
NOTE: If the
or
button is pressed while TYPE is
highlighted, then Sync Type is switched between Separate
Sync and Sync On Green.
OSM LOCK OUT
The OSM LOCK OUT control completely locks out access
to all OSM control functions. When attempting to activate
OSM controls while in the LOCK OUT mode, a screen will
appear indicating that OSM controls are locked out.
• To enter the LOCK OUT mode, simultaneously press
the PROCEED and button. The LOCK OUT window
will appear.
• To activate the LOCK OUT function, simultaneously
press and hold down the PROCEED and button. The
OSM window will disappear within seconds and the
LOCK OUT function will be activated.
• To deactivate the LOCK OUT mode, simultaneously
press the PROCEED and
button.
78134811.PM5
27
99.12.24, 2:19 PM
E - 18
Specifications
Multisync LCD2110
Display
54.1 cm (21.3 inch) viewable image size; 1600 x 1200
native resolution (Pixel Count); active matrix;
thin film transistor (TFT); liquid crystal display (LCD);
0.27 mm dot pitch; 180 cd/m2 white luminance, typical;
250:1 contrast ratio, typical
Input Signal
Video
Sync
Analog 0.7 Vp-p 75 Ω
Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative)
(TTL Level)
Sync on Green video (Positive) 0.7
Vp-p and sync. Negative 0.3 Vp-p
Display Colours Analog Input:
Synchronisation Horizontal
Unlimited number of colours
(Depends on the graphics board)
24.0 kHz to 82.0 kHz (Automatically)
56.0 Hz to 76.0 Hz (Automatically)
Range
Vertical
Resolutions
Supported
Landscape
720 x 400*: VGA text
640 x 480* at 60 Hz to 76 Hz
800 x 600 at 56 Hz to 76 Hz
832 x 624* at 75 Hz
1024 x 768* at 60 Hz to 76 Hz
1280 x 960* at 60 Hz to 76 Hz
1280 x 1024* at 60 Hz to 76 Hz
1600 x 1200** at 60 Hz
Portrait
480 x 640* at 60Hz to 76Hz
600x 800 at 56 Hz to 76 Hz
624 x 832* at 75 Hz
768 x 1024* at 60 Hz to 76 Hz
960 x 1280* at 60 Hz to 76 Hz
1024 x 1280* at 60 Hz to 76 Hz
1200 x 1600** at 60 Hz
Active Display
Area***
Landscape
Portrait
Horizontal
Vertical
Horizontal
Vertical
432 mm
324 mm
324 mm
432 mm
78134811.PM5
28
99.12.24, 2:19 PM
Specifications
E - 19
Power supply
Current Rating
Dimensions
AC 100-120 V / 220-240 V @ 50/60 Hz
DC 24V
@ 100-120V / 0.9A @ 220-240V / 0.5A
@ DC 24V / 3.3A
Landscape
Portrait
Hight Adjust
498(W) x 501(H) x 246(D) mm
417(W) x 541(H) x 246(D) mm
80mm
Weight
11.5kg
Operating
Environmental
Considerations
Temperature
Humidity
5° C to + 35° C
30% to 80%
Storage
Environmental
Considerations
Temperature
Humidity
-10° C to + 60° C
10% to 85%
* Interpolated Resolutions: when resolutions are shown that are lower than the pixel
count of the LCD module, text may appear choppy or lines may appear to be bold. This
is normal and necessary for all current flat panel technologies, each dot on the screen is
actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution
must be done. When the interpolated resolutions is not an exact multiple of the native
resolution, the mathematical interpolation necessary may cause some lines to appear
thicker than others.
** NEC cites recommended resolutions at 60 Hz for optimal display performance.
*** Active display area is dependent upon the signal timing.
Technical specifications are subject to change without notice.
78134811.PM5
29
99.12.24, 4:10 PM
E - 20
Troubleshooting/Support
Troubleshooting/Support
Problem
Check These Items
No picture
- The signal cable should be completely connected to
the display card/computer.
- The display card should be completely seated in its
slot.
- Power button and computer power switch should be
in the ON position.
- Check to make sure that a supported mode has been
selected on the display card or system being used.
(Please consult display card or system manual to
change graphics mode.)
- Check the monitor and your display card with respect
to compatibility and recommended settings.
- Check the signal cable connector for bent or pushed-
in pins.
- Check that the BNC/D-SUB button is in the correct
position.
Power Button does Unplug the power cord of the monitor from the AC
not respond
outlet to turn off and reset the monitor, or simultaneously
press the RESET and Power buttons.
Image persistence
Image persistence is when a “ghost” of an image
remains on the screen even after the monitor has been
turned off. Unlike CRT monitors, LCD monitors’
image persistence is not permanent. To alleviate image
persistence, turn the monitor off for as long as an image
was displayed. If an image was on the monitor for one
hour and a ”ghost” of that image remains, the monitor
should be turned off for one hour to erase the image.
NOTE: As with all personal display devices, NEC
recommends using a screen saver at regular intervals
whenever the screen is idle.
78134811.PM5
30
99.12.24, 2:19 PM
Troubleshooting/Support
E - 21
Problem
Cheak These Items
- Signal cable should be completely attached to the
Image is unstable,
unfocused or
swimming is
apparent
computer.
- Use the OSM Image Adjust controls to focus and
adjust display by increasing or decreasing the Fine Control.
When the display mode is changed, the OSM Image
Adjust settings may need to be re-adjusted.
- Check the monitor and your display card with respect
to compatibility and recommended signal timings.
- If your text is garbled, change the video mode to
non-interlace and use 60Hz refresh rate.
LED on monitor is - Power Switch should be in the ON position and power
not lit (no green or cord should be connected.
amber colour can be - Make certain the computer is not in a power-saving
seen)
Display image has a Select “TYPE” in the OSM Information menu
green cast to it press the or Control button.
Display image is not - Use the OSM Image Adjust controls to increase or
mode (touch the keyboard or mouse).
and
sized properly
decrease the H. Size.
- Check to make sure that a supported mode and signal
timing has been selected on the display card or system
being used. (Please consult display card or system
manual to change graphics mode or refresh rate.)
78134811.PM5
31
99.12.24, 2:19 PM
|