jWIN
jWIN Electronics Corporation
digital generation
JTP670
2 L I N E / 1 3 M E M O R Y S P E A K E R P H O N E
OWNER’S MANUAL
and
OPERATING INSTRUCTIONS
FEATURES :
-
-
-
-
-
-
-
-
-
-
-
-
13 MEMORY AUTODIAL (3 ONE TOUCH/ 10 TWO TOUCH
TONE/PULSE DIALING
RINGER LED LIGHT
WALL OR DESK USE
HEARING AID COMPATIBLE
FLASH/HOLD/REDIAL/MUTE BUTTONS
RINGER HI/LO/OFF CONTROL
RECEIVER VOLUME CONTROL
SPEAKERPHONE VOLUME CONTROL
2-LINE HANDS-FREE SPEAKERPHONE
3 PARTY CONFERENCING
IN USE LED INDICATOR
DIAGRAM
LINE 1 BUTTON
INDEX FOR LISTING
NUMBERS IN MEMORY
STORE BUTTON
RECEIVER VOLUME CONTROL
LINE 2 BUTTON
RECEIVER
MUTE BUTTON
STORE BUTTON
ONE TOUCH MEMORY
BUTTONS (M1, M2, M3)
VOLUME CONTROLS FOR: RINGER AND
MUTE BUTTON
REDIAL BUTTON
IN-USE INDICATOR LIGHT
SPEAKER AND TOUCH PULSE BUTTON
SPEAKER BUTTON
AUTO BUTTON
2
OPERATING INSTRUCTIONS
SET UP
1. Open the cover of the battery compartment and insert four AA batteries. (Not included)
2. Connect the coiled cord to receiver and the telephone base.
3. Connect the telephone wire to the telephone set and wall jack
TONE/PULSE SELECTOR
Select the type of dialing that you desire or that your telephone system requires.
•
•
TONE
The unit will operate using tone dialing.
PULSE
The unit will dial using rotary dial type pulses.
RINGER VOLUME CONTROL
The volume control for the incoming call ringer is located on the right side of the phone
console. Select the desired volume/function of the tone ringer:
• OFF
indicates that the ringer volume is turned off and there will be no sound to
signal an incoming call. Note: the flashing light will indicate an incoming call.
LO indicates the ringer volume will be diminished but can be heard.
HI indicates maximum ringer volume.
• LO/HI
SPEAKER (HANDS-FREE) VOLUME CONTROL
The volume control button for the speaker is located on the right side of the phone console.
Slide the control from Min to Max to adjust the volume.
MAKING CALLS
1. Select the desired dialing mode with the Tone/Pulse selector. (Do this only once when
you set up your phone.)
2. Select a phone line by pressing either the “LINE 1” or “LINE 2” button.
3. Pick up the receiver or press SPEAKER button and wait for a dial tone.
4. Dial your call.
RECEIVING CALLS
When the phone rings, the red light will flash which indicates that there is an incoming call.
1. Lift the receiver and speak into the mouthpiece.
2. Hang up the receiver to release the telephone line when the conversation is
completed.
3
USING THE SPEAKERPHONE
HANDSFREE CALLING
Press the SPEAKER button, the In-Use LED will light. The unit is ready for use as a
speakerphone without lifting the receiver. You can listen to the caller through the phone’s
speaker. The sound level can be adjusted by sliding the volume control located on the
right side of the console.
HANDSFREE ANSWERING
You can use the speakerphone when you cannot or do not wish to pick up the phone
receiver. As a courtesy, be sure to inform the other party that he or she may be heard by
other listeners on the phone speaker.
1. Press the SPEAKER button. The In-Use Indicator will light up.
2. Begin speaking.
USING BOTH PHONE LINES
With two telephone lines, you can have the convenience of placing one call on hold while
you answer or initiate another call. You also have the capability of conferencing both lines.
(See CONFERENCING)
Example:
1. When you are on LINE 1 and there is an incoming call from LINE 2. (Red light on LINE
2 will blink.)
2. Press the HOLD button to hold you call on LINE 1.
(A green light on LINE 1 will blink which indicates this line is on HOLD status.)
3. Press the Line 2 button to answer the incoming call.
LAST NUMBER REDIALING
The last number you called can be redialed automatically. This is useful especially if the
number you are calling is busy.
1. Pick up the receiver or press the SPEAKER button to get a new dial tone.
2. Press the REDIAL button.
If you have any difficulty getting a dial tone, do the following:
• Press the Hook Switch or hang up the phone for 2 seconds.
- Or -
• Press “Flash”. Then press the Redial button.
This phone will remember the last number dialed even overnight. If you do not want the
number to reside in the phone memory, pick up the phone receiver and press any number.
4
TRANSFERRING CALLS
When in an office equipped with PABX, your unit makes it easy to transfer calls.
• Ask the calling party to wait.
• Press and release the flash button.
• Dial the number of the party you wish to transfer to.
• When the party answers, announce the call.
• Hang up.
If you receive a busy signal or no answer:
• Press the flash button to re-connect to your party.
HOLD BUTTON
To put your party on hold position, press the HOLD button.
RELEASING HOLD
Press either the LINE 1 or LINE 2 button and speak to the holding party.
PAUSE BUTTON
In some case, such as PABX or for some long distance services, a pause should be
included in the dialing sequence. This unit provides a stackable pause function (3.6
sec/pause).
MUTE BUTTON
To prevent the other party on the line from hearing a private conversation you may be
holding with someone else, press the MUTE button, and keep it depressed. Release the
button to resume your phone conversation.
FLASH BUTTON
To return to the dial tone or retrieve another call while using the phone (as indicated by a
call waiting beep), press the ‘FLASH’ button once.
STORING PHONE NUMBERS IN ONE-TOUCH DIAL MEMORY (M1, M2, M3)
You can store up to 3 phone numbers in one-touch memory. These numbers are assigned
to the M1, M2, and M3 buttons. Reserve these buttons for your most frequently used
phone numbers.
1. Lift the receiver or press the SPEAKER button.
2. Press the STORE button.
3. Enter the number you want to store.
4. Press one of the (M1/M2/M3) buttons to store the phone number in the desired
memory location.
5
5. Replace the receiver or press the SPEAKER button to end the procedure.
STORING PHONE NUMBERS IN TWO-TOUCH DIAL MEMORY (AUTODIAL)
You can store up to 10 phone numbers in two-touch memory. These numbers are
assigned to any number key on the keypad. Reserve these buttons for numbers you use
frequently.
1. Lift the receiver.
2. Press the STORE button.
3. Enter the phone number you want to store.
4. Press the STORE button again.
5. Press a number from 0 to 9 (to assign storage of the phone number). You can list
these numbers in the index space provided on the console.
6. Hang up.
DIALING A NUMBER FROM ONE-TOUCH (M1/M2/M3) MEMORY
1. Get a dial tone (use either the receiver or speakerphone).
2. Press one of the 3 buttons. The stored phone number will dial automatically.
DIALING A NUMBER FROM AUTODIAL MEMORY
1. Get a dial tone (use either the receiver or speakerphone).
2. Press the AUTO button.
3. Press the numerical button to which the phone number is assigned. The unit will
automatically dial the phone number stored in memory for the key you selected.
CONFERENCING
When you have two parties on two separate lines:
• Press the ‘CONF’ button and you can speak with both parties in a three-way
conversation.
CANCELING THE CONFERENCE FUNCTION
• Press the ‘CONF’ button again to release the function.
IN USE INDICATOR
This LED will light when you lift the receiver-showing you that the phone is functioning.
This will also serve to signal you if the receiver is off the hook or not properly seated in the
base.
When there is an incoming call, the LED will flash until you lift the receiver.
6
‘P-T’ KEY
During pulse dialing mode, the ‘P-T’ key provides automatic switching from pulse mode to
tone mode by pressing the ‘P-T’ key. The tone information can be stored into memory for
autodial and redial functions.
7
IMPORTANT SAFETY INSTRUCTIONS
When using this unit, basic safety precautions should always be followed to reduce the
risk of fire, electric shock, or personal injury.
Please read all instructions thoroughly.
Follow all warnings and instructions included with this unit.
1. Unplug this unit from AC outlets before cleaning.
2. Do not use liquid or aerosol cleaners.
3. Use a damp cloth for cleaning.
4. Do not use this unit near water, for example, near a bathtub, washbowl, sink, or the
like. This telephone is an electrical device and can be hazardous if immersed in
water. If you accidentally drop it into water, first unplug it from the wall jack AC
outlet, and then remove it from the water.
5. Place this unit securely on a stable surface. Serious damage and/or injury may
result if the unit falls.
6. Do not cover slots and openings on the unit. They are provided for ventilation and
protection against overheating.
7. Never place the unit near radiators, or in a place where proper ventilation is not
provided.
8. Do not use or put the unit in extreme temperatures.
9. Use only the power source marked on the unit. If you are not sure of the type of
power supplied in your home, consult your dealer or local power company.
10.Do not place objects on the power cord. Install the unit where no one can step or
trip on the cord.
11.Do not overload wall outlets and extension cords. This can result in the risk of fire
or electric shock.
12.Never push any objects through slots in this unit. This may result in the risk of fire
or electric shock.
13.To reduce the risk of electric shock, do not disassemble this unit. Sent the unit to
jWIN Customer Service Department when service is required.
14.Opening or removing covers may expose you to dangerous voltages or other risks.
15.Incorrect reassembly can cause electric shock when the unit is subsequently used.
16.Unplug this unit from the wall outlet and refer servicing to jWIN customer service
when the following conditions occur:
• When the power supply cord or plug is damaged or frayed
• If liquid has been spilled into the unit
• If the unit doesn’t work normally after following the operating instructions.
• If the unit has been dropped or physically damaged
8
• If the unit exhibits a distinct change in performance
17.Adjust only controls covered by the operating instructions. Improper adjustments
may require extensive work by jWIN Customer Service Department.
18.During thunderstorms, avoid using telephones except cordless types. There may
be a remote risk of electric shock from lightening.
19.Do not use this unit to report a gas leak when in the vicinity of the leak. Please
remove yourself immediately from the area and make the emergency phone call in
a safe area.
20.Do not modify or tamper with the telephone’s internal components. Improper
adjustment can cause damage and may be dangerous.
Caution:
To reduce the risk of fir or injury to persons, read and follow these instructions.
• Do not dispose of the batteries in a fire. They may explode. Check local waste
management codes for special disposal instructions.
• Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.
• Exercise care in handling batteries in order not to short the battery to conductive
materials such as rings, bracelets, and keys. The battery and/or conductor may
overheat and cause burns.
• Charge the battery(ies) provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.
Warning:
To prevent a shock hazard, do not expose this product to rain or any type of moisture.
The AC adapter is used as the main power connection. Be sure that the AC outlet is
located/installed near the unit and is easily accessible.
SAVE THESE INSTRUCTIONS
9
FOR PRODUCT SERVICE
Get in touch with jWIN if you require additional products or servicing for your jWIN
equipment. We invite you to call us or contact us via the internet:
• Call 1-866-807-jWIN
When you ship the product:
• Carefully pack your unit, preferably in the original carton.
• Attach a letter to the outside of the carton detailing the problem.
• Be sure to include all parts of the product.
• Include a $6 check or money order for shipping and handling.
• Include a return address that is not a PO Box.
• Include your phone number if you would like to know the disposition of your product.
Send the unit to:
jWIN Electronics, Corp.
CUSTOMER SERVICE DEPARTMENT
51-4-1 59TH Place
Woodside, NY 11377
Problem:
_____________________________________________________________________
10
|